Shop
Analog PH Sensor Kit
1.800,00 EGP- Module power supply: 5 VDC.
- Measuring temperature: 0-50 ℃.
- Response time: ≤ 1min.
- pH sensor with BNC connector.
- Gain adjustment Potentiometer.
- Power indicator LED.
Arduino mega 2560 ATmega2560-16AU Board
1.400,00 EGP✅ 54 Digital I/O pins with 15 PWM
✅ 4 UARTs and 16 analog inputs
✅ 256 KB Flash, 8 KB SRAM, 4 KB EEPROM
✅ 100% Arduino IDE compatible
✅ Perfect for large-scale embedded projects
Arduino MEGA 2560 R3 with CH340 Chip
Original price was: 1.250,00 EGP.1.200,00 EGPCurrent price is: 1.200,00 EGP.- Programmer: CH340
- Operating Voltage 5V
- Input Voltage (recommended) 7-12V
- Input Voltage (limits) 6-20V
- Digital I/O Pins 54 (of which 15 provide PWM output)
- Analog Input Pins 16
- DC Current per I/O Pin 40 mA
- DC Current for 3.3V Pin 50 mA
- Flash Memory 256 KB of which 8 KB used by bootloader
Arduino Nano 3.0 Controller Board – FT232
290,00 EGP- Based on ATmega328 microcontroller
- FT232 USB-to-Serial driver for stable PC communication
- Compact and breadboard-friendly design
- 22 total I/O pins (14 Digital, 8 Analog)
- Supports serial, I2C, and SPI communication
- Onboard voltage regulator (5V & 3.3V)
- Preloaded with Arduino bootloader for easy programming
- Ideal for IoT, robotics, sensors, and embedded systems
Arduino Nano Cable – USB 2.0 A to USB 2.0 Mini B
20,00 EGP- Compatible with Arduino Nano V3 (Mini USB port)
- USB 2.0 A to Mini-B 5-pin connector
- Supports data transfer rates up to 480 Mbps
- Compact 30cm length – perfect for desktop setups
- Plug-and-play; no drivers needed
Arduino Nano Type-C USB
250,00 EGP- Model Name/Number Arduino NANO
- Memory 32 KB of Which 2 KB Used By Bootloader
- Processor ATmega328
- USB 2.0 Ports Mini USB
- No. Of Cores Single
- Digital I/O Pin 22
- Weight 7g
Arduino Nano V3.0 CH340 Chip Board，Atmega328P
Original price was: 250,00 EGP.210,00 EGPCurrent price is: 210,00 EGP.- Operating Voltage (logic level): 5V
- With Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
Arduino UNO R3 CH340G ATMega328P
330,00 EGP- ATmega328 SMD microcontroller with Arduino bootloader
- Operating voltage: 5V; input 7-12V recommended
- 14 digital I/O pins (6 PWM), 6 analog inputs
- 32 KB Flash memory, 16 MHz clock speed
- CH340 USB-to-serial interface (driver may be needed)
- Fully compatible with Arduino IDE and libraries
- Includes USB cable for easy programming
Arduino Uno R3 Without Cable
440,00 EGP- ✅ ATmega328P microcontroller
✅ 14 digital and 6 analog I/O pins
✅ USB programming interface (USB cable sold separately)
✅ Compatible with Arduino IDE and shields
✅ Ideal for beginners and hobbyists
Arduino UNO R4 Minima
Original price was: 850,00 EGP.750,00 EGPCurrent price is: 750,00 EGP.- Same form factor as UNO R3
- Extra onboard peripherals
- Inbuilt HID Support
- Expanded Memory and Faster Clock Speed than before
Arduino UNO R4 WiFi
Original price was: 1.400,00 EGP.1.100,00 EGPCurrent price is: 1.100,00 EGP.- Same form factor as UNO R3
- Inbuilt Wi-Fi and Bluetooth
- Onboard 12×8 LED Matrix
- Extra onboard peripherals
- Inbuilt HID Support
- Expanded Memory and Faster Clock Speed than before
ATMEGA328P-U without bootLoader
220,00 EGP- 131 powerful instructions – Most Single Clock Cycle Execution
- 32 x 8 general purpose working registers
- Fully static operation
- Up to 20MIPS throughput at 20MHz
- On-chip 2-cycle multiplier
- Write/erase cycles: 10,000 flash/100,000 EEPROM
- Optional boot code section with independent lock bits
- In system programming by on-chip boot program
- True read while write operation
- Programming lock for software security
- Two 8-bit timer/counters with separate prescaler and compare mode
- One 16-bit timer/counter with separate prescaler, compare mode, and capture mode
- Real-time counter with separate oscillator
Battery Charger for 18650 Li-ion 1 Cell YH-07
50,00 EGP-
Designed for 1×18650 Li-ion battery (3.7V)
-
Compact and portable charging dock
-
LED indicators: Red (charging), Green (fully charged)
-
Built-in protection: overcharge, short-circuit, reverse polarity
-
USB-powered – compatible with wall adapters, laptops, power banks
-
Ideal for flashlights, DIY projects, and battery testing
Battery Holder ( 1 x 18650 ) (3.7v)
12,00 EGP- 🔹 Holds 1 x 18650 battery (3.7V)
- 🔧 Pre-soldered leads for easy connection
- 🧱 Made of high-quality plastic
- 🛠️ Easy to install and use
- ⚠️ Compatible with standard 18650 batteries (not included)
Battery Holder ( 2 x 18650 ) (3.7v)
20,00 EGP- Hold 2 standard 18650 batteries.
- Wire Length: 15 cm.
- Output: 7.2v.
- Dimension (Appro.) : 76 x 40 x 20 mm
- Weight: 12gm
- High-quality plastic material
Battery Holder ( 3 x 18650 ) (3.7v)
25,00 EGP- Hold 3 standard 18650 batteries.
- Wire Length: 15 cm.
- Output: 11.1 V.
- Dimension (Appro.) : 76 x 60 x 18 mm.
- Weight: 18 gm.
- High-quality plastic material
Battery Holder for CR2025/CR2032 PCB Mount
4,50 EGP-
Compatible with CR2025 & CR2032 coin cell batteries
-
PCB Mountable for secure and stable installation
-
Metal Contacts provide reliable electrical connection
-
Compact Design suitable for slim electronic devices
-
Durable Plastic Housing ensures long-lasting performance
Battery Holder for CR2450 PCB Mount
8,00 EGP-
Fits CR2450 Coin Cell (3V lithium battery)
-
PCB Mount Design for stable soldering
-
Secure Metal Contacts ensure reliable power connection
-
Compact & Low-Profile ideal for embedded and wearable projects
-
Durable Plastic Body for long-term use
