Shop
Brand
MQ-135 Air Quality/Gas Detector Sensor Module For Arduino
100,00 EGP- Detects multiple gases: NH₃, benzene, alcohol, CO₂, NOₓ, smoke
- Provides analog and digital outputs
- Operates at 5V DC
- Adjustable sensitivity via onboard potentiometer
- Requires preheating (~24 hours) for accurate readings
- Compact and easy to integrate
MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module
85,00 EGP- Detects smoke, LPG, butane, hydrogen, and other combustible gases
- Provides analog and digital output signals
- Fast response and high sensitivity
- Compatible with Arduino and other microcontrollers
- Easy to calibrate and use in gas leak detection projects
- Operates at 5V power supply
- Ideal for safety and environmental monitoring systems
MQ-5 Gas Sensor Module
80,00 EGP- Detects LPG, methane, natural gas, and propane
- Dual output: analog and digital signals
- Operates at 5V with low power consumption
- Adjustable sensitivity via onboard potentiometer
- Fast response and recovery time
- Compact and easy to integrate
MQ-7 CO Carbon Monoxide Coal Gas Sensor Module
75,00 EGP- Operating voltage: DC 5 V.
- The analog output voltage, the higher the concentration the higher the voltage.
- The carbon monoxide detection with better sensitivity.
- With a long service life and reliable stability.
- Rapid response and recovery characteristics.
- Range: 10 to 1000 ppm.
MT6701 14-Bit Magnetic Angle Sensor Module (AS5600 Alternative)
250,00 EGP- 🧲 14-bit magnetic angle sensor for precise rotation measurement
- 🎯 Smooth, high-resolution output (AS5600 alternative)
- 🧩 Ideal for knobs, robotics joints, gimbals, and encoders
- 🚌 I2C interface for easy connection to microcontrollers
- ⚡ Low power operation—great for portable/always-on systems
- 📐 Works with common diametric magnets for angle sensing
- 🛠️ Compact module—easy to mount and integrate
- ✅ Great choice for contactless angle sensing with long life
Multicolor 10 pin Dupont Flat Ribbon Cable (1 Meter)
25,00 EGP-
10 Individual Jumper Leads in a flat, ribbon format with 2.54 mm pitch
-
One-Meter Length for flexible routing in electronics projects
-
Multicolor Wires for easy signal identification and organization
-
Female-to-Female Connectors for quick plug-and-play with headers
-
Compatible with Breadboards & Microcontrollers like Arduino, Raspberry Pi
NEO-6M GPS Module with EPROM
500,00 EGP- Based on u-blox NEO-6M GPS chip
- Tracks up to 22 satellites on 50 channels
- High sensitivity: -161 dBm, low power: 45mA
- Built-in 25x25mm ceramic patch antenna
- Default baud rate: 9600
- EEPROM for saving settings & backup battery for faster lock
- TTL UART Interface: TX, RX, VCC, GND
- Supports GPS functions: Position hold, Return-to-Home, Waypoints
- Cold start: 38s, Hot start: 1s
- Compact: 30mm x 23mm module, 3mm mounting holes
- Ideal for drones, robots, navigation projects
NEO-M8N GPS Module with Ceramic Active Antenna
800,00 EGP- 📡 NEO-M8N GPS module with ceramic active antenna
- 🛰️ High-sensitivity positioning for fast, stable GPS lock
- 📍 Provides accurate location, speed, and time data
- 🔌 UART interface (and I2C/SPI depending on board)
- 🧩 Ideal for drones, robotics, trackers, and navigation projects
- ⚡ Works with common microcontrollers and flight controllers
- 📦 Compact module—easy to mount and integrate
- ✅ Great choice for outdoor positioning and timing applications
NJK-5002C Hall Effect Sensor – NPN NO 3-Wire Magnet | Arduino Compatible
245,00 EGP- NPN Normally Open (NO) magnetic switch
- 3-wire connection: VCC, GND, Output
- Wide voltage range: 4.5V–30V DC
- Built-in LED indicator for magnetic detection
- Fast, non-contact sensing
- Compatible with Arduino and other microcontrollers
- Durable and compact M12 threaded design
NodeMCU ESP32-S Development Board (38pin) DRIVER CH340C
450,00 EGPProduct Highlights
- Dual Connectivity: Integrated 2.4GHz Wi-Fi and Dual-mode Bluetooth (Classic + BLE).
- Powerful Processing: Dual-core 240MHz Xtensa® processor for high-speed multitasking.
- Expanded 38-Pin Layout: Maximum GPIO access, perfect for breadboard prototyping.
- CH340C Serial Driver: Stable and easy USB-to-Serial communication with modern OS support.
- IoT Ready: Ultra-low power consumption with advanced deep-sleep modes.
NRF24L01 Wireless Module With Antenna
325,00 EGP- 2.4GHz transceiver for wireless data
- Long range with external antenna
- Low power, SPI interface
- Ideal for IoT, Arduino, wireless sensors
ON/OFF PCB Switch (6 Pin)
5,00 EGP- 6-pin configuration for secure PCB mounting
- Slim, compact build ideal for confined layouts
- Durable materials ensure long-lasting operation
- Simple installation across various circuit types
- Perfect for prototypes, gadgets, and home electronics
