- تكلفه فاتورة الكهرباء
- Electrical Energy Consumption
- Parallel and Series Resistor Calculator
- LED Resistor Calculator
- UPS Battery Backup Calculator
- Voltage Divider Calculator
- Resistor Color Code Calculator
- Ohm’s Law Calculator
- Current Divider Calculator
- Number System Conversion Calculator
- Boost Converter Calculator
- MOSFET Threshold Voltage Calculator
- Apparent Power Calculator (kVA & VA)
- 555 Timer Calculator
- Buck Converter Calculator
- Capacitors in Series or Parallel Calculator
- Low Pass Filter Calculator
- RMS Voltage Calculator
- Universal Data Converter
- RMS Voltage Calculator
- Capacitor Code Converter
- Series Inductors Calculator
Shop
Showing 361–380 of 483 results
- Too many add to cart attempts. Please wait before trying again.
MOC3063 Zero-Crossing Optocoupler – 600V Triac Driver for Safe AC Load Control
15,00 EGP- Zero-Crossing Detection – Ensures low-noise switching and reduced EMI
- 600V Peak Voltage Handling – Ideal for switching high-voltage AC loads
- Low Trigger Current – Operates with typical 10mA LED current
- Optical Isolation – Withstands up to 5300V RMS between input and output
- Safe AC Switching – Protects microcontrollers and PLCs from AC surges
- Compact DIP-6 Package – Easy PCB integration and through-hole mounting
- Reliable Load Control – Perfect for lamps, motors, heaters, and industrial systems
- Wide Operating Range – -40°C to +100°C for industrial-grade environments
Mounting for DC Motor JGA25-370-CE 3D Printed
45,00 EGP-
Designed for 25mm JGA25-370-CE gear motors
-
High-quality PLA/PETG 3D printed construction
-
Pre-drilled 3mm mounting holes
-
Stable, low-profile design (~20mm height)
-
Easy alignment using motor faceplate and side screws
-
Ideal for robotics, pan-tilt, or DIY mechanical projects
MP3-TF-16P SD Card MP3 Module with Serial Port
150,00 EGP- Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
- 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
- Fully supports FAT16, FAT32 file system
- Maximum support 32G TF card
- Support U disk to 32G, 64M bytes of NORFLASH
- A variety of control modes are available. IO control mode, serial mode, AD key control mode
MPU GY-6500 6-Axis Gyroscope and Acceleration Sensor Module
Original price was: 300,00 EGP.275,00 EGPCurrent price is: 275,00 EGP.- 6-Axis Sensor: Combines 3-axis gyroscope and 3-axis accelerometer.
- Adjustable Sensitivity: Selectable ranges for both accelerometer and gyroscope.
- I2C Communication: Easy integration with Arduino, Raspberry Pi, and other microcontrollers.
- Low Power Consumption: Ideal for battery-powered applications.
- Compact Size: Easy to mount on various platforms.
- Wide Application Range: Perfect for motion tracking, robotics, drones, and wearable devices.
MPU9250 9-Axis Sensor Module – Gyroscope, Accelerometer, and Magnetometer for Robotics, and Wearable Devices
Original price was: 750,00 EGP.725,00 EGPCurrent price is: 725,00 EGP.- Accelerometer, Gyroscope
- Power Supply: DC3.3V-5V
- Chip: MPU9250
- Size: 22 mm x 17 mm.
- Gyro range : ± 250 500 1000 2000 ° / s
- Acceleration range: ± 2 ± 4 ± 8 ± 16g
- 9 DOF modules
MQ-135 Air Quality/Gas Detector Sensor Module For Arduino
100,00 EGP- Detects multiple gases: NH₃, benzene, alcohol, CO₂, NOₓ, smoke
- Provides analog and digital outputs
- Operates at 5V DC
- Adjustable sensitivity via onboard potentiometer
- Requires preheating (~24 hours) for accurate readings
- Compact and easy to integrate
MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module
85,00 EGP- Detects smoke, LPG, butane, hydrogen, and other combustible gases
- Provides analog and digital output signals
- Fast response and high sensitivity
- Compatible with Arduino and other microcontrollers
- Easy to calibrate and use in gas leak detection projects
- Operates at 5V power supply
- Ideal for safety and environmental monitoring systems
MQ-5 Gas Sensor Module
80,00 EGP- Detects LPG, methane, natural gas, and propane
- Dual output: analog and digital signals
- Operates at 5V with low power consumption
- Adjustable sensitivity via onboard potentiometer
- Fast response and recovery time
- Compact and easy to integrate
MQ-7 CO Carbon Monoxide Coal Gas Sensor Module
75,00 EGP- Operating voltage: DC 5 V.
- The analog output voltage, the higher the concentration the higher the voltage.
- The carbon monoxide detection with better sensitivity.
- With a long service life and reliable stability.
- Rapid response and recovery characteristics.
- Range: 10 to 1000 ppm.
Multicolor 10 pin Dupont Flat Ribbon Cable (1 Meter)
25,00 EGP-
10 Individual Jumper Leads in a flat, ribbon format with 2.54 mm pitch
-
One-Meter Length for flexible routing in electronics projects
-
Multicolor Wires for easy signal identification and organization
-
Female-to-Female Connectors for quick plug-and-play with headers
-
Compatible with Breadboards & Microcontrollers like Arduino, Raspberry Pi
NJK-5002C Hall Effect Sensor – NPN NO 3-Wire Magnet | Arduino Compatible
245,00 EGP- NPN Normally Open (NO) magnetic switch
- 3-wire connection: VCC, GND, Output
- Wide voltage range: 4.5V–30V DC
- Built-in LED indicator for magnetic detection
- Fast, non-contact sensing
- Compatible with Arduino and other microcontrollers
- Durable and compact M12 threaded design
NRF24L01 Wireless Module With Antenna
325,00 EGP- 2.4GHz transceiver for wireless data
- Long range with external antenna
- Low power, SPI interface
- Ideal for IoT, Arduino, wireless sensors
ON/OFF PCB Switch (6 Pin)
5,00 EGP- 6-pin configuration for secure PCB mounting
- Slim, compact build ideal for confined layouts
- Durable materials ensure long-lasting operation
- Simple installation across various circuit types
- Perfect for prototypes, gadgets, and home electronics
On/Off Switch Black Rocker 10A Small 12V DC (KDC-08)
5,00 EGP- MPN: KDC-08
- Temperature: -25 to 85 degc
- Rated voltage: 250V
- Rated current: 3A-6A-15A
- contact resistance: <=0.02 ohm
- Insulation resistance: >=100Mohm
- withstand voltage: 1500VAC
- lifetime: 10000 cycles
Optical Dust Sensor with Cable – Smoke
350,00 EGP- Infrared optical sensing for accurate particle detection
- Detects dust, smoke, and pollen in indoor environments
- Fast response time (<1 second) and low power use
- Compact build with lightweight materials
- Plug-and-play with included 5-pin interface cable
- Compatible with Arduino, ESP32, STM32, Raspberry Pi
PCB LINE FR2 (9X15 cm2)
35,00 EGP- Material: Durable FR2 phenolic paper laminate.
- Size: Compact 9×15 cm².
- Copper-Clad: Single-sided for easy soldering.
- Grid Pattern: 2.54 mm (0.1 inch) spacing for standard components.
- Pre-drilled Holes: ~1 mm diameter for through-hole components.
- Versatile Use: Ideal for prototyping, hobby, and educational projects.
PCB LINE IC FR2 (9X15 cm2)
35,00 EGP-
Pre-etched copper tracks for ICs and components
-
Optimized for DIP packages, resistors, and capacitors
-
Made from FR2 phenolic paper – easy to cut and drill
-
9×15 cm² single-layer board for prototyping
-
Standard 2.54mm hole pitch for through-hole components
-
Ideal for educational, DIY, and quick prototyping projects
Ekosta Electronics Egypt
Ekosta Electronics Egypt | Leading Supplier of Arduino, Raspberry Pi, Motor Drivers & Electronics Components | Premium Spare Parts, Industrial Sensors & Robotic Kits | High-Quality Electronics at Competitive Prices | Fast Shipping & Expert Technical Support Across Egypt.
